GYX-PFA is a soft flow and jet flow high temperature dyeing machine built on an L-shaped slope formed by three connected storage zones. The shape takes the low liquor ratio of a round machine and the wide fabric suitability of an L machine, while leaving behind the narrow suitability of the first and the high water demand of the second.
The chamber is fed through a selectable nozzle and returns through a selectable lower pipe, so flow character and finish effect are two independent choices rather than one fixed design.






The Three Storage Zones
Upper layer
Cloth is received into the storage zone as it leaves the nozzle.
Slide section layer
Cloth travels down the slope under smooth guidance.
Bottom layer
Cloth rests, then is re-fed into the circuit.
Because the stack spreads across three zones instead of one, it is guided rather than compressed, which is where the reduction in squeezing and crease marks comes from. A gas-liquid separation arrangement gives the cloth a bulking action, supported by a fabric arranging hopper.
Nozzle Options
|
Nozzle |
Available sizes |
Function |
|
Span nozzle (S) |
70 / 80 / 90 / 110 / 130 |
General purpose; balances nozzle angle against flow |
|
SF nozzle |
70 / 80 / 90 / 110 |
Combines the strengths of span and filament nozzles |
|
Parallel nozzle (P) |
70 / 80 / 90 / 110 |
Parallel angle; moves cloth by flow for gentle processing |
Capacity Range
|
Item |
GYX-PFA-300 |
GYX-PFA-600 |
GYX-PFA-900 |
GYX-PFA-1200 |
|
Chamber / cloth tank No. |
1 |
2 |
3 |
4 |
|
Capacity (kg) |
300 |
600 |
900 |
1200 |
|
Liquor volume (kg) |
1200-1800 |
2400-3600 |
3600-5400 |
4800-7200 |
|
Main Pump Motor (kW) |
22 |
37 |
45 |
55 |
|
Max Temperature |
140 °C |
140 °C |
140 °C |
140 °C |
|
Max Pressure |
4 kg/cm² |
4 kg/cm² |
4 kg/cm² |
4 kg/cm² |
|
Fabric Speed |
330-700 m/min |
330-700 m/min |
330-700 m/min |
330-700 m/min |
|
Steam Consumption |
411 |
840 |
1350 |
1680 |
|
Cooling Water |
1950 |
3900 |
5850 |
7800 |
|
Length L (mm) |
10118 |
10118 |
10118 |
10118 |
|
Width W (mm) |
1800 |
3010 |
4180 |
5575 |
|
Height H (mm) |
3360 |
3360 |
3360 |
3360 |
Fabric Coverage Map
|
Fabric group |
Nozzle route |
Pressure |
Reason |
|
Resilient and low-tension fabrics |
Soft flow / overflow |
0.5 - 1.0 kg/cm² |
Low spray pressure keeps the surface intact |
|
High-density woven |
Jet flow |
up to 3 kg/cm² |
Force needed to penetrate the construction |
|
Microfiber |
Jet flow |
up to 3 kg/cm² |
Liquor must reach the yarn core to wet out |
|
Mixed programme |
SF nozzle |
set per fabric |
One nozzle spans two fabric families |
Nozzles are fitted with a double anti-rotation device so the rope stays stable in the stream at any of the pressure settings above.
Where To Find Utility And Pipe Detail
This page carries the full model table for the series. Water and steam balance by model, including the slide-chamber water level comparison, is on the extra large capacity page; lower pipe selection and nozzle pairing are on the three layer chamber page.
Workshop


Hot Tags: soft flow jet high temperature dyeing machine, China soft flow jet high temperature dyeing machine manufacturers, suppliers, High Temperature Airflow Dyeing Machine, High Temperature High Pressure Jet Dyeing Machine, Ht Jet Dyeing Machine, jet dyeing machine, Low Liquor Ratio Jet Dyeing Machine, Rapid Ht Jet Dyeing Machine











