Lightweight woven and knit constructions are the least forgiving load in a high-temperature dyehouse. The cloth carries very little mass, so almost any surface it drags across will leave a mark, and the faster it runs the faster those marks accumulate. The common answer is a speed limit. The HOL Jet Flow High Temperature Dyeing Machine answers the same problem by taking away the surfaces the cloth would otherwise drag across.
Two components do that work. The guide tube is kept full of liquor, so the fabric travels suspended rather than sliding along a wall. Inside the tube a wave-profiled net carries the stack, and the wave shape spreads the bearing area instead of concentrating it on one line. Together they allow the cloth to run at 150-500 m/min without the surface damage that speed usually costs.
How The Cloth Is Carried
Liquid-filled guide tube
The fabric floats, so it never meets a dry tube wall.
Wave-profiled inner net
Load is distributed over the crests, not over one flat surface.
N-form cloth advance
The rope opens as it travels, which keeps rope creases and curled selvedges from setting in.
Tail-end steam setting with dual-path guiding
Thin cloth runs as two short fast loops instead of one long loop.
Liquor Ratio In Practice
Liquor ratio is selected at 1:5 or 1:6 according to fabric type and process requirement. A ratio is easy to quote and hard to picture, so the table below converts it into mass for a typical batch. The 1:10 column is a reference point for a conventional deep bath, not a BOSEN rating.
|
Item |
At 1:6 |
At 1:10 (reference) |
Difference |
|
Batch size |
600 kg |
600 kg |
same load |
|
Liquor in circulation |
3,600 kg |
6,000 kg |
2,400 kg less to heat |
|
Thermal input, 20 to 130 °C |
approx. 1.66 GJ |
approx. 2.77 GJ |
approx. 1.1 GJ (about 307 kWh) less |
|
Ramp time at 20 °C/min |
approx. 5.5 min |
approx. 5.5 min |
rate limited, not mass limited |
Indicative arithmetic only, taking water at 4.19 kJ/(kg·K) across a 20-130 °C rise. Real steam demand depends on heat recovery, insulation and the recipe in use.
The practical consequence is not the number in the last column but where it lands: a smaller bath reaches temperature sooner, needs less cooling water to come back down, and leaves less liquor to drain and treat at the end of the cycle.
The Three Chamber Counts
|
Item |
HOL-1-300 |
HOL-2-600 |
HOL-4-1200 |
|
Chamber No. |
1 |
2 |
4 |
|
Capacity (kg) |
300-400 |
600-800 |
1200-1600 |
|
Main Pump Motor |
30 HP (22 kW) |
60 HP (45 kW) |
100 HP (75 kW) |
|
Max Temperature |
140 °C |
140 °C |
140 °C |
|
Max Pressure |
4 kg/cm² |
4 kg/cm² |
4 kg/cm² |
|
Fabric Speed |
150-500 m/min |
150-500 m/min |
150-500 m/min |
|
Heating Rate 20-130 °C |
20 °C/min |
20 °C/min |
20 °C/min |
|
Cooling Rate 130-80 °C |
15 °C/min |
15 °C/min |
15 °C/min |
|
Length L (mm) |
7800 / 8550 / 9300 |
7800 / 8550 / 9300 |
7800 / 8550 / 9300 |
|
Overall Length L1 (mm) |
9300 / 10050 / 10800 |
9300 / 10050 / 10800 |
9300 / 10050 / 10800 |
|
Width W (mm) |
2200 |
3600 |
6500 |
|
Height H (mm) |
3100 |
3100 |
3100 |
Site Conditions To Confirm
Floor length: L 7800 / 8550 / 9300 mm, overall L1 9300 / 10050 / 10800 mm.
Width W 2200 / 3600 / 6500 mm; height H is 3100 mm on all three models.
Power supply against main pump motor 22 / 45 / 75 kW.
Headroom above the chamber for loading and for maintenance access to the net.
How The Companion Pages Divide The Detail
The table above is the complete dimensional and rating reference for the series. Energy behaviour and the surface-protection measures are worked through on the low energy page and the fabric guiding page, which use the same platform.






Hot Tags: jet flow high temperature dyeing machine, China jet flow high temperature dyeing machine manufacturers, suppliers, Eco Friendly Jet Dyeing Machine, High Temperature Airflow Dyeing Machine, Ht Jet Dyeing Machine, Hthp Jet Dyeing Machine, jet dyeing machine, Rapid Ht Jet Dyeing Machine











